Sunny Vaccum Flask Water Bottle

Please read this instruction manual carefully before using the product and keep it in a safe place.

Accessories: Plastic and rubber parts are consumables. Under normal use, they need to be inspected approximately once a year. If there is surface damage or unevenness, it is a normal wear and tear phenomenon. Please purchase new parts to replace them in time.

Instructions for use: For best results, please preheat (pre-cool) the cup by adding a small amount of hot water (or ice water) before use. Add hot water (or ice water), screw on the lid, and let it sit for 30 seconds to 1 minute before pouring out the hot water (or ice water). It is then ready for normal use.

Precautions: 1. Do not store carbonated beverages; 2. Do not use for prolonged moisturizing of dairy products or baby food (risk of bacterial growth); 3. Do not heat the product using microwave ovens or other heating equipment; 4. Do not wash in a dishwasher.

The following types of food are prohibited from being put in the container: 1. Effervescent tablets, dry ice, and carbonated beverages (to avoid the risk of increased internal pressure, which could cause the stopper to become stuck or the contents to spray out); 2. Acidic beverages such as plum juice and lemon juice (to corrode the inner liner if stored for too long); 3. Foods that are prone to bacterial growth, such as baby food, dairy products, and fruit juice (to increase the risk of bacterial growth if stored for too long).

Certificate

Standard implemented: GB/T29606 Stainless Steel Vacuum Cup

GB4806.7 National Food Safety Standard - Plastic Materials and Products for Food Contact

GB 4806.9 National Food Safety Standard - Metal Materials and Articles for Food Contact

GB 4806.11 National Food Safety Standard - Rubber Materials and Products for Food Contact

Stainless steel type: austenitic stainless steel

Product name

Fun Plush Toy Double Drink Cup

Specification

450-500ml

Insulation efficiency

6:35 AM

Cooling efficiency

6h≤15°C

Thermal insulation performance: After the product is left open at 20℃±5℃ for more than 30 minutes, boiling water (100℃) is poured in until the bottom of the sealing cap (stopper) is reached. When the actual measured water temperature inside the product reaches 95℃±1℃, the seal is immediately tightened. Under the same environmental conditions, the water temperature inside the product is measured after 6 hours.

Cold retention performance: After the product is left open at 20℃±5℃ for more than 30 minutes, fill it with 0℃ water up to the bottom of the sealing cap (stopper). When the actual measured water temperature inside the product reaches 5℃±1℃, immediately tighten the seal. Under the same environmental conditions, measure the water temperature inside the product after 6 hours.

Product Name: Fun Plush Toy Double Drinking Cup

Specifications: 450-500mL

Quality inspection certificate: qualified

Made of stainless steel, with a double-sealed design, large diameter, and easy to clean.

Instructions for use: 1. When using this product for the first time, please clean it with a neutral detergent.

Precautions: 1. This product is suitable for temperatures from 0℃ to 100℃; 2. Not suitable for dishwashers, microwave ovens, or ovens; 3. This product is for hand washing only. Do not use chlorine bleach; 4. Do not store carbonated beverages or use for prolonged insulation of dairy products or baby food (risk of bacterial growth); 5. When containing hot drinks, do not extend the bottle above the neck and keep it out of reach of infants and young children; 6. Avoid dropping or subjecting to strong impacts to prevent loss of insulation or cold retention function; 7. Do not store salty or oily liquids.

Storage method: Store in a cool, dry place.

Main materials: Inner liner: austenitic stainless steel 06Cr19Ni10 (304); Outer shell: austenitic stainless steel 06Cr19Ni10 (304); Bottom: anti-slip TPE pad; Lid: PP/polymer of propylene and ethylene (propylene accounts for the largest mass); Sealing ring: silicone rubber/methyl vinyl dimethylsiloxane and polysiloxane)